C e l l u l a r T e l e p h o n y by B r i a n O b l i v i o n A -=Restricted -=Data -=Transmission The benefit of a mobile transceiver has been the wish of experimentors since the late 1800's. To have the ablility to be reached by another man despite location, altitude, or depth has had high priority in communication technology throughout its history. Only until the late 1970's has this been available to the general public. That is when Bell Telephone (the late MaBell) introduced the Advanced Mobile Phone Service, AMPS for short. Cellular phones today are used for a multitude of different jobs. They are used in just plain jibber-jabber, data transfer(I will go into this mode of cellular telephony indepth later), corporate deals, surveillance, emergencies, and countless other applications. The advantages of cellular telephony to the user/phreaker are obvious: 1. Difficulty of tracking the location of a transciever (especially if the transciever is on the move) makes it very difficult to locate 2. Range of the unit within settled areas 3. Scrambling techniques are feasible and can be made to provide moderate security for most transmissions. 4. The unit, with modification can be used as a bug, being called upon by the controlling party from anywhere on the globe. 5. It with the right knowledge one can modify the cellular in both hardware and software to create a rather diverse- iffied machine that will scan, store and randomly change ESN's per call there by making detection almost impossible. I feel it will be of great importance for readers to understand the background of the Cellular phone system, mainly due to the fact that much of the pioneering systems are still in use today. The first use of a moblie radio came about in 1921 (remember prohibition?) by the Detroit police department. This system operated at 2Mhz. In 1940, frequencies between 30 and 40Mhz were made available to and soon became overcrowded. The trend of overcrowding continues today. In 1946, the FCC declared a 'public corresponence system' called, or rather classified as "Domestic Public Land Mobile Radio Service" (DPLMRS) at 35 - 44 Mhz band that ran along the highway between New York and Boston. Now the 35-44MHz band is used mainly by Amateur radio hobbiest's due to the bands susceptibility to skip-propogation. These early mobile radio systems were all PTT(push-to-talk) systems that did not enjoy todays duplex conversations. The first real mobile 'phone' system was the 'Improved Mobile Telephone Service' or the IMTS for short, in 1969. This system covered the spectrum from 150 - 450MhHz, sported automatic channel selection for each call, eliminated PTT, and allowed the customer to do thier own dialing. From 1969 to 1979 this was the mobile telephone service that served the public and business community, and it is still used today. IMTS frequencies used(MHz): Channel Base Frequency Mobile Frequency VHF Low Band ZO 35.26 43.26 ZF 35.30 43.30 ZH 35.34 43.34 ZA 35.42 43.32 ZY 34.46 43.46 ZC 35.50 43.50 ZB 35.54 43.54 ZW 35.62 43.62 ZL 35.66 43.66 VHF High Band JL 152.51 157.77 YL 152.54 157.80 JP 152.57 157.83 YP 152.60 157.86 YJ 152.63 157.89 YK 152.66 157.92 JS 152.69 157.95 YS 152.72 157.98 YA 152.75 158.01 JK 152.78 158.04 JA 152.81 158.07 UHF Band QC 454.375 459.375 QJ 454.40 459.40 QO 454.425 459.425 QA 454.45 459.45 QE 454.475 459.475 QP 454.50 459.50 QK 454.525 459.525 QB 454.55 459.55 QO 454.575 459.575 QA 454.60 459.60 QY 454.625 459.625 QF 454.650 459.650 VHF High frequencies are the most popular frequencies of all the IMTS band. VHF low bands are used primarily in rural areas and those with hilly terrain. UHF bands is primarily used in cities where the VHF bands are overcrowded. Most large cities will find at least one station being used in their area. ADVANCED MOBILE PHONE SYSTEM The next step for Mobile telephone was made in 1979 by Bell Telephone, again (gee.. where was the competition?), introducing the Advanced Mobile Phone Service. This service is the focus of this document, which has now taken over the mobile telephone industry as the standard. What brought this system to life were the new digital technologies of the 1970's. This being large scale integrated custom circuits and microprocessors. Without these technologies, the system would not have been economically possible. The basic elements of the cellular concept have to do with frequency reuse and cell splitting. Frequency reuse refers to the use of radio channels on the same carrier frequency to cover different areas which are seperated by a signifigant distance. Cell splitting is the ability to split any cell into smaller cells if the traffic of that cell requires attitional frequencies to handle all the area's calls. These two elements provide the network an opportunity to handle more simul- taneous calls, decrease the transmitters/receivers output/input wattage/gain and a more universal signal quality. When the system was first introduced, it was allocated 40mHz in the frequency spectrum, divided into 666 duplex radio channels providing about 96 channels per cell for the seven cluster frequency reuse pattern. Cell sites (base stations) are located in the cells which make up the cellular network. These cells are usually represented by hexagons on maps or when developing new systems and layouts. The cell sites contain radio, control, voice frequency processing and maintnence equipment, as well as transmitting and receiving antennas. The cell sites are inter- connected by landline with the Mobie Telecommunications Switching Office (MTSO). In recent years, the FCC has added 156 frequencies to the Cellular bandwidth. This provides 832 possible frequencies available to each subscriber per cell. All new cellular telephones are built to accomodate these new frequencies, but old cellular telephones still work on the system. How does a cell site know if the unit is old or new? Let me explain. The problem of identifying a cellular phones age is done by the STATION CLASS MARK (SCM). This Numer is 4 bits long and broken down like this: Bit 1: 0 for 666 channel usage (old) 1 for 832 channel usage (new) Bit 2: 0 for a mobile unit(in vehical) 1 for voice-activated transmit (for protables) Bit 3-4: Indentify the power class of the unit Class I 00 = 3.0 watts Continuous Tx's 00XX...DTX <> 1 Class II 01 = 1.2 watts Discont. Tx's 01XX...DTX = 1 Class III 10 = 0.6 watts reserved 10XX, 11XX Reserved 11 = --------- Letters DTX set to 1 permits use of discontinuous trans- missions Cell Sites: How Cellular telephones get their name Cell sites, as mentioned above are layed out in a hexagonal type grid. Each cell is part of a larger cell which is made up of seven cells in the following fashion: |---| ||===|| |---| |---| |---| |--- / \ // \\ / \ / \ / \ / | |===|| 2 ||===|| ||===|| |---| |---| \ // \ / \\ // \\ / \ / \ |---|| 7 |---| 3 ||==|| 2 ||==|| |---| |---| / \\ / \ // \ / \\ Due to the \ | ||---| 1 |---|| 7 |---| 3 ||--| difficulty of | \ // \ / \\ / \ // \ representing / |--|| 6 |---| 4 ||--| 1 |---|| |graphics with | / \\ / \ // \ / \\ / ascii characters\ | ||==|| 5 ||==|| 6 |---| 4 ||--| I will only show | \ / \\ // \\ / \ // \ two of the cell / |---| ||===|| ||===|| 5 ||==|| |types I am trying- / \ / \ / \\ // \ / to convey. \ | |---| |---| ||==|| |---| |---| | \ / \ / \ / \ / \ / \ / |---| |---| |---| |---| |---| |---| As you can see, each cell is a 1/7th of a larger cell. Where one(1) is the center cell and two(2) is the cell directly above the center. The other cells are number around the center cell in a clockwise fashion, ending with seven(7). The cell sites are equiped with three directional antennas with an RF beamwidth of 120 degrees providing 360 degree coverage for that cell. Note that all cells never share a common border. Cells which are next to each other are obviously never assigned the same frequencies. They will almost always differ by at least 60 Khz. This also demonstrates the idea behind cell splitting. One could imagine that the parimeter of one of the large cells was once one cell. Due to a traffic increase, the cell had to be sub-divided to provide more channels for the subscribers. Note that subdivisions must be made in factors of seven. There are also Moblie Cell sites, which are usually used in the transisitional period during the upscaling of a cell site due to increased traffic. Of course, this is just one of the many uses of this component. Imagine you are building a new complex in a very remote location. You could feasibly install a few mobile cellular cell sites to provide a telephone-like network for workers and executives. The most unique component would be the controller/ transceiver which provides the communications line between the cell site and the MTSO. In a remote location such a link could very easily be provided via satellite up/down link facilities. Lets get into how the phones actually talk with eachother. There are several ways and competitors have still not set an agreed upon standard. Frequency Division Multiple Access (FDMA) This is the traditional method of traffic handling. FDMA is a single channel per carrier analog method of transmitting signals. There has never been a definate set on the type of modulation to be used. There are no regulations requiring a party to use a single method of modulation. Narrow band FM, single sidband AM, digital, and spread-spectrum techniques have all been considered as a possible standard. But none hae yet to be chosen. FDMA works like this: Cell sites are constantly searching out free channels to start out the next call. As soon as a call finishes the channel is freed up and put on the list of free channels. Or, as a subscriber moves from one cell to another the new cell they are in will hopefully have an open channel to recieve the current call in progress and carry it through its location. This process is called handoff, and will be discussed more indepth further along. Other proposed traffic handling schemes include Time-Division Multiple Acces (TDMA), Code-Division Multiple Access(CDMA), and Time-Division/Frequency Division Multiple Access. Time Division Multiple Access With TDMA calls are simultaneously held on the same channels, but are mutiplexed between pauses in the conversation. These pauses occur in the way people talk and think, and the telephone company also injects small delays on top of the conversation to accommodate other traffic on that channel. This increase in the length of the usual pause results in a longer amount of time spent on the call. Longer calls result in higher cost of the call. Code Division Multiple Access This system has been used in mobile military communications for the past 35 years. This system is digital and breaks up the digitized conversation into bundles, compressed, sent, then decompressed and converted back into analog. There are said increases of throughput of 20 : 1 but CDMA is susceptible to interference which will result in packet retransmission and delays. Of course error correction can can help in data integrity, but will also result in a small delay in throughput. Time-Dvision/Frequency Division Multiple Access TD/FDMA is a relatively new system which is an obvious hybrid of FDMA and TDMA. This system is mainly geared towards the increase of digital transmission over the cellular network. TD/FDMA make it possible to transmit signals from base to moblie without disturbing the conversation. With FDMA there are signifigant disturbances during handoff with prevent continual data transmission from site to site. TD/FDMA make it possible to transmit control signals by the same carrier as the data/voice thereby ridding extra channel usage for control. Cellular Frequency Usage and channel allocation There are 832 cellular phone channels which are split into two seperate bands. Band A consists of 416 channels for non-wireline services. Band B consists equally of 416 channels for wireline services. Each of these channels are split into two frequencies to provide duplex operation. The lower frequency is for the mobile unite while the other is for the cell site. 21 channels of each Band are dedicated to 'control' channels and the other 395 are voice channels. You will find that the channels are numbered from 1 to 1023, skipping channels 800 to 990. I found these handy-dandy equations that can be used for calculating frequencies from channels and channels from frequencies. N = Cellular Channel # F = Cellular Frequency B = 0 (mobile) or B = 1 (cell site) CELLULAR FREQUENCIES from CHANNEL NUMBER: F = 825.030 + B * 45 + ( N + 1 ) * .03 where: N = 1 to 799 F = 824.040 + B * 45 + ( N + 1 ) * .03 where: N = 991 to 1023 CHANNEL NUMBER from CELLULAR FREQUENCIES N = 1 + (F - 825.030 - B * 45) / .03 where: F >= 825.000 (mobile) or F >= 870.030 (cell site) N = 991 + (F - 824.040 - B * 45) / .03 where: F <= 825.000 (moblie) or F <= 870.000 (base) Now that you have those frequencies, what to do with them. Well, for starters, one can very easily monitor the cellular frequencies with most hand/base scanners. Almost all scanners pre-1988 have some coverage of the 800 - 900 MHz band. All scanners can monitor the IMTS frequencies. Remember that cellular phones operate on a full duplex channel. That means that one frequency is used for transmission and the other is used for receiving, each spaced exactly 30 Khz apart. Remember also that the base frequencies are 45MHz higher than the cellular phone frequencies. This can obviously make listening rather difficult. One way to listen to both parts of the conversation would be having two scanners programmed 45 Mhz apart to capture the entrire conversation. The upper UHF frequency specrum was 'appropriated' by the Cellular systems in the late 1970's. Televisions are still made to recieve up to channel 83. This means that you can recieve much of the cellular system on you UHF receiver. One television channel occupies 6Mhz of bandwidth. This was for video, sync, and audio transmission of the channel. A cellular channel only takes up 24 KHz plus 3KHz set up as a guard band for each audio signal. This means that 200 cellular channels can fit into one UHF television channel. If you have an old black and white television drop a variable cap in there to increase the sensistivity of the tuning. Some of the older sets have coarse and fine tuning knobs. Some of the newer, smaller, portable television sets are tuned by a variable resistor. This make modifications MUCH easier, for now all you have to do is drop in there a smaller value pot and tweak away. I have sucessfully done this on two televisions. Most users will find that those who don't live in a city will have a much better listening rate per call. In the city, the cells are so damn small that handoff is usually every other minute. Resulting in chopped conversations. If you wanted to really get into it, I would suggest to obtain an old Television set with decent tuning controls and remove the RF section out of the set. You don't want all that hi-voltage circuitry lying around(flyback and those caps). UHF recievers in televisions downconvert UHF frequencies to IF (intermediate frequencies) between 41 and 47 MHz. These output IF frequencies can then be run into a scanner set to pick-up between 41 - 47 MHz. Anyone who works with RF knows that it is MUCH easier to work with 40MHz signals than working with 800MHz signals (not to far away from Ghz.. mmmmmmm.. Waveguides are just sooo much fun). JUST REMEMBER ONE THING!!!! Isolate the UHF reciever from your scanner by using a coupling capacitor(.01 - .1 microfarad(50V min.) will do nicely)!!!! You don't want any of those biasing voltages creeping into your scanners recieving AMPLIFIERS!!! Horrors. Also, don't forget to gound both the scanner and reciever. Some systems transmit and recieve the same cellular transmission on the base frequencies. There you can simply hang out on the base frequency and capture both sides of the conversation. The handoff rate is much higher in high traffic areas leading the listener to hear short or choppy conversations. At times you can listen in for 5 to 10 minutes per call, depending on how fast the caller is moving through the cell site. TV Cell & Channel Scanner TV Oscillator Band Channel Freq.& Number Frequency Frequency Limit =================================================================== 73 (first) 0001 - 825.03 45.97 871 824 - 830 73 (last) 0166 - 829.98 41.02 871 824 - 830 74 (first) 0167 - 830.01 46.99 877 830 - 836 74 (last) 0366 - 835.98 41.02 877 830 - 836 75 (first) 0367 - 836.01 46.99 883 836 - 842 75 (last) 0566 - 841.98 41.02 883 836 - 842 76 (first) 0567 - 842.01 46.99 889 842 - 848 76 (last) 0766 - 847.98 41.02 889 842 - 848 77 (first) 0767 - 848.01 46.99 895 848 - 854 77 (last) 0799 - 848.97 46.03 895 848 - 854 All frequencies are in MHz You can spend hours just listening to cellular telephone conversations but I would like to mention that it is illegal to do so. Yes, it is illegal to monitor cellular telephone conversations. It just another one of those laws like removing tags off of furniture and pillows. It's illegal, but what the hell for? Its also illegal to spit on the sidewalks here in Massachusetts, yet you can carry a shotgun on sundays with you to mass(thats still in the books. Obviously it was for the original settlers). At any rate, I just want you to understand that doing the following is in violation of the law. Now back to the good stuff. Conversation is not only what an avid listener will find on the cellular bands. One will also hear call/channel setup control data streams, dialing, and other control messages. At times, a cell site will send out a full request for all units in its cell to indentify itself. The phone will then respond with the appropriate identification on the corresponding control channel. Whenever a moblie unit is turned on, even when not placing a call, whenever there is power to the unit, it transmits its phone number and its 8-digit ID number. The same process is done when an idling phone passes from one cell to the other. This process is repeated for as long as there is power to the unit. This allows the MTSO to 'track' a mobile through the network. That is why it is not a good reason to use a mobile phone from one site. They do have ways of finding you. And it really is not that hard. Just a bit of RF Triangulation theory and you're found. However, when the power to the unit is shut off, as far as the MTSO cares, you never existed in that cell, of course unless your unit was flagged for some reason. MTSO's are basically just ESS sytems designed for mobile applications. This will be explained later within this document. It isn't feasible for the telephone companies to keep track of each customer on the network. Therefore the MTSO really doesn't know if you are authorized to use the network or not. When you purchase a cellular phone, the dealer gives the units phone ID number to the local BOC, as well as the number the BOC assigned to the customer. When the unit is fired up in a cell site its ID number and phone number is transmitted and checked. If the two numbers are registered under the same subscriber, then the cell site will allow the mobile to send and recieve calls. If they don't match, then the cell will not allow the unit to send or recieve calls. Hence, the most successful way of reactivating a cellular phone is to obtain an ID that is presently in use and modifying your rom/prom/eprom for your specific phone. RF and AF Specifications: Everything that you will see from here on out is specifically Industry/FCC standard. A certian level of compatibility has to be maintained for national intercommunications, therefore a common set of standards that apply to all Cellular telephones can be compiled and analyzed. Transmitter Mobiles: audio transmission - 3 kHz to 15 kHz and 6.1 kHz to 15 kHz - 5.9 kHz to 6.1 kHz 35 dB attenuation - Above 15 kHz, the attenuation becomes 28 dB - All this is required after the modulation limiter and before the modulation stage Transmitters Base Stations: audio transmission - 3 kHz to 15 kHz - Above 15 kHz, attenuation required 28 dB - Atennuation after modulation limiter - no notch filter required RF attenuation below carrier Transmitter: audio transmission - 20 kHz to 40 kHz, use 26 dB. - 45 kHz to 2nd harmonic, the specification is 60 dB or 43 + 10 log of mean output power - 12 kHz to 20 kHz, attenuation 117 log f/12 - 20 kHz to 2nd harmonic, there is a choice: 100 log F/100 or 60 dB or 43 log + 10 log of mean output power, whichever is less. Wideband Data - 20 kHz to 45 kHz, use 26 dB - 45 kHz to 90 kHz, use 45 dB - 90 kHz to 2nd harmonic, either 60 dB or 43 + 10 log mean output power - all data streams are encoded so that NRZ (non-return-to-zero) binary ones and zeroes are now zero-to-one and one-to-zero transitions respectively. Wideband data can then modulate the transmitter carrier by binary frequency shift keying(BFSK) and ones and zeroes into the modulator must now be equivalent to nominal peak frequency deviations of 8 kHz above and below the carrier frequency. Supervisory Audio Tones - Save as RF attenuation measurements Signaling Tone - Same as Wideband Data but must be 10 kHz +/- 1 Hz and produce a nominal frequency deviation of +/- 8 kHz. The previous information will assist any technophile to modify or even troubleshoot his/her cellular phone. Those are the working guidelines, as I stated previously. UNIT IDENTIFICATION Each mobile unit is identified by the following sets of numbers. The first number is the Moblie Identification Number (MIN). This 34 bit binary number is derived from the units telephone number, MIN1 is the last seven digits of the telephone number and MIN2 is the area code. For demonstrative purposes, we'll encode 617-637-8687. Here's how to derive the MIN2 from a standard area code. In this example, 617 is the area code. All you have to do is first convert to modulo 10 using the following function. A zero digit would be considered to have a value of 10. 100(first number) + 10(second) +1(third) - 111 = x 100(6) + 10(1) + 1(7) - 111 = 506 (or you could just - 111 from the area code.) Then convert it to a 10-bit binary number: 0111111010 To derive MIN1 from the phone number is equally as simple. First encode the next three digits, 637. 100(6) + 10(3) + 1(7) - 111 = 526 Converted to binary: 1000001110 The remainder of the number 8687, is processed further by taking the first digit, eight(8) and converting it directly to binary. 8 = 1000 (binary) The last three digits are processed as the other two sets of three numbers were processed. 100(6) + 10(8) + 1(7) - 111 = 576 Converted to binary: 1001000000 So the completed MIN number would look like this: |--637---||8-||---687--||---617--| 1000001110100010010000000111111010 \________/\__/\________/\________/ A unit is also identifiable by its Electronic Serial Number or ESN. This number is Factory Preset and is usually stored in a ROM chip, which is soldered to the board. It may also be found in a 'computer on a chip', which are the new microcontrollers which have rom/ram/microprocessor all in the same package. This type of setup usually has the ESN and the software to drive the unit all in the same chip. This makes is significantly harder to dump, modify and replace. But it is far from impossible. The ESN is a 4 byte hex or 11-digit octal number. I have encountered mostly 11-digit octal numbers on the casing of most celluar phones. the first three digits represent the manufacturer and the remaining eight digits are the units ESN. I'll go more into the ESN later in the document. The Station Class Mark (SCM) is also used for station identification by providing the station type and power output rating. This was already discussed in a previous section. The System IDentification (SID number is a number wich represents the mobile's home system. This number is 15-bits long and a list of current nationwide SID's should either be a part of this file or it will be distrubted along with it. In the next issue we'll discuss the Control channels, signalling formats, and dissecting the NAM in detail. Social.technological impacts (re: cellular interception designed into the units) -------------- cut me here --------------------------------------------------- PUTTING IT ALL TOGETHER - Signaling on the Control Channels There are two types of continuous wideband data stream transmissions. One is the Forward Control Channel which is sent from the land station to the mobile. The other is the Reverse Control Channel, which is sent from the mobile to the land station. Each data stream runs at a rate of 10 kilobit/sec, +/- 1 bit/sec rate. The formats for each of the channels follow. Forward Control Channel The forward control channel consists of three discrete information streams. They are called stream A, stream B and the busy-idle stream. All three streams are multiplexed together. Messages to mobile stations with the least significant bit of thier MIN number equal to "0" are sent on stream A, and those with a "1" are sent on stream B. The busy-idle stream contains busy-idle bits, whic are used to indicate the status of the reverse control channel. If the busy-idle bit = "0" the reverse control channel is busy, if it equals "1" it is idle. The busy-idle bit is located at the beginning of each dotting sequence, word sync sequence, at the beginning of the first repeat of word A and after every 10 message bits thereafter. Mobile stations achieve synchronization with the incoming data via a 10 bit dotting sequence (1010101010) and an 11 bit word sync sequence (11100010010). Each word contains 40 bits, including parity and is repeated 5 times after which it is then refered to as a "block". For a multiword message, the second word block and subsequent word blocks are formed the same as the first word blok including the dotting and sync sequences. A "word" is formed when the 28 content bits are encoded into a (40, 28; 5) BCH (Bose-Chaudhuri-Hocquenghem) code. The left-most bit shall be designated the most-signifigant bit. The Generator polynominal for the (40, 28;5) BCH code is: 12 10 8 5 4 3 0 G (X) = X + X + X + X + X + X + X B Each FOCC message con consist of one or more words. Messaging trans- mitted over the forward control channel are: - Mobile station control message - Overhead message - control-filler mesage Controller-filler messages may be inserted between messages and between word blocks of a multiword message. Message Formats: Found on either stream A or B MOBILE STATION CONTROL MESSAGE The mobile station control message can consist of one, two, or four words. Word 1 (abbreviated address word) +--------+-------+---------------------------------------+-----------+ | T t | | | | | 1 2 | DCC | Moblie Identification Number 1 | P | | | | 23-0 | | +--------+-------+---------------------------------------+-----------+ bits: 2 2 24 12 Word 2 (extended address word) +------+-----+-----------+------+--------+-------+----------+-----+ | T T |SCC =| | RSVD | LOCAL | CRDQ | ORDER | | | 1 2| 11 | MIN2 | = 0 | | | | | | = +-----+ 3-24 +------+-----+--+-------+----------| P | | 10 |SCC =| | VMAC | CHAN | | | | 11 | | | | | +------+-----+-----------+------------+---------------------+=----+ The Reverse Control Channel (RECC) is a wideband data stream sent from the moblie station to the land station. This data stream runs at a rate of 10 kilobit/sec, +/- 1 bit/sec rate. The format of the RECC data stream follows: +---------+------+-------+------------+-------------+-----------+----- | Dotting | Word | Coded | first word | Second word | Third word| | | sync | DCC | repeated | repeated | repeated | ... | | | | 5 times | 5 times | 5 times | +---------+------+-------+------------+-------------+-----------+----- DCC = Digital Color Code Dotting = 01010101...010101 Received DCC 7-bit Codec DCC Word sync = 11100010010 00 0000000 01 0011111 10 1100011 11 1111100 All messages begin with the RECC seizure precursor with is composed of a 30 bit dotting sequence (1010...101), and 11 bit word sync sequence (11100010010), and the coded digital color code. Each word contains 48 bits, including parity, and is repeated five times after which it is refered to as a word block. A word is formed by encoding 36 content bits into a (48, 36) BCH code that has a distance of 5, (48 36; 5). The left most bit shall be designated the most-significant bit. The 36 most-significant bits of the 48 bit field shall be the content bits. The generator polynomial for the code is the same for the (40,28;5) code used on the forward channel. CONTROL CHANNELS (SETUP CHANNELS) Each wireline and non-wireline service have 21 channels. These channels are used by the MTSO and the cell sites to directly communicate with the mobile unit. The first signal sent to initiate a call is the Supervisory Audio Tone (SAT). This can be thought of as the voltage used to close the loop on a land telephone. SAT Tones with corresponding binary codes: 5970 Hz (00) 6000 Hz (01) 6030 HZ (10) The mobile unit recieves the SAT from the cell site and transponds it back (closing the loop). Tone recognition must take place within 250 milliseconds or the site interprets it as the mobile is out of range. If the SAT is returned, then a Signaling Tone is issued. This Tone is 10kHz and is present when the user is either being alerted(call initialization), being handed off, or disconnecting The Signaling tone is used only in mobile to land direction