So this guy asked me how to get digitized Macintoshª sounds into a modem, so he can play them over the phone line during a conversation. Lions roaring when he calls customer service, that sort of thing... The simple answer is, it canÕt be done. Most modems donÕt have the necessary digital-analog-converter (DAC) circuit. Voicemail units, like the DoveFax+ª, are another story. But every Mac has a DAC built-in! ItÕs what beeps, boings, and insults you with Talking Mooseª. You just need to connect it to your phone. A few months ago, I posted a circuit that would let you connect any Macª to almost any phone circuit. Since then, IÕve been e-mailed countless letters of thanks (well, more than two). But some folks asked for more: ÒWhy canÕt it be louder?Ó ÒWill it work with stereo sounds in my newer Mac?Ó ÒHow can I use it with my home stereo or Walkmanª?Ó ÒWhat is the meaning of life, the universe, and everything?Ó For the answer to most of these questions, read on... ---------------------------------------------------------------- STEREO? LOUDER? Original Macs (most compact models, from the 128 up through the SEª series) had a low-current audio output jack: it worked well with an amplifier, but didnÕt have enough oomph [technical term] to drive headphones. So the first circuit I devised just matched that output to the phone system. It wasnÕt particularly loud, but it worked with any Mac. Newer Macs have a more powerful output jack. So I modified the circuit to use that power to boost the voltage going to the phone. At the same time, I doubled it so you could use it to pick up both sides of stereo sounds (theyÕll be mono on the other end of the phone line, of course), or to connect your phone to a stereo amp or tape player. Which circuit fits your Mac? You can tell by plugging a pair of headphones into the back. If they play in stereo with full volume, use Circuit II. If they sound kind of wimpy, use Circuit I... and donÕt leave the phones plugged in. ---------------------------------------------------------------- CIRCUIT I Read this even if youÕre building the other version. Some of the descriptions apply to both. YouÕll want a circuit like this: Ê IÕve included Radio Shack¨ stock numbers, but you should be able to find equivalent items at any electronic store or hackerÕs closet. PLUG - 1/8" mini plug to fit your Mac. Compact Macs and older Mac II models with mono output can use a 2-conductor plug, #274-286. SWITCH - Any single-pole, double-throw switch. #275-635 is a good possibility, or you can use knife switches, three-way wall switches, or block switches from the model train you abandoned when you bought a computer. TRANSFORMER - This is the key to the whole thing. It keeps the Mac and The Phone Companyª from interfering with each other. If you donÕt use one, youÕll probably disable your phone service. Any low-power 1:1 audio transformer should work. You can rip one out of that 300-baud modem youÕve been meaning to toss, or get a #273-1374 for under four bucks. (If you get the Radio Shack transformer, cut the Scotchª tape wrapped around it to free up the four wires. The wire colors should match the diagram.) CAPACITOR - This isnÕt necessary for transmitting sound, but it lets you hang up your phone. Otherwise, the phone system will think the transformer is an active telephone. Get a film or ceramic capacitor rated at least .1 µF at 75 volts. Slightly higher ratings arenÕt a problem. #272-1053 (.1 µF / 200 volts) is a good choice. Electrolytic capacitors wonÕt work. SPEAKER (optional) - Using the sound output of your Mac disables its internal speaker. Pull the plug out to turn the speaker back on. Or wire in a substitute, #40-246 (or any other small low-power speaker, like the one from that 300-baud modem). It wonÕt be as loud as the internal speaker, which could be a good thing. YouÕll also need some hookup wire, to extend the components and reach your telephone. Use bell wire, #278-1509, or anything else in your basement or on Radio ShackÕs shelf. ---------------------------------------------------------------- CIRCUIT II Build one of these: Ê The parts are the same, except the transformers are audio-output stepdown ones, used backwards. Radio Shack #273-1380 does the job nicely. (YouÕll need two of them, but theyÕre cheap.) The plug should be a stereo Òring-tip-sleeveÓ one: #274-284 matches newer Macs and most Walkpersons; use #274-139 for most home stereo amps. Or rip the cord off a pair of non-functioning headphones. I left the switch and speaker off the drawing of this circuit, but you can add them if you want. You can also leave out one transformer, if youÕre dealing with a mono circuit (but _donÕt_ tie the tip and the ring of the plug together; that can harm your Mac). The transformer color codes might change, so follow these simple rules: 1. Note how one side of the transformer has two wires, and the other has three. The two-wire side connects to the Mac. The three-wire side faces the phone. The middle wire on the three-wire side doesnÕt connect to anything. 2. Note how white is wired to white, and green is wired to green. Even if you use transformers with different colors, the two sides of the stereo circuit must match. Otherwise, stereo sounds will be mangled and mono ones will disappear entirely. ---------------------------------------------------------------- CONSTRUCTION Both the MacÕs audio output and the standard phone system are low-voltage. Special wiring techniques arenÕt needed. Solder or twist the wires together neatly, and insulate the connections with electrical tape (or even duct tape, Scotch Tapeª, or Band-Aidsª). It doesnÕt matter which wires go where on the speaker or capacitor. If youÕre using a stereo plug (circuit II), notice how the middle wire goes to the tip of the plug, the top wire goes to the ring partway up the plug, and the bottom wire goes to the plugÕs sleeve. Follow the color codes, and Ñ if youÕre using a switch Ñ make sure the wire from the Mac goes to the switchÕs center connector. Put the whole mess in a box to make it look pretty. I used part of an old intercom: the speaker and switch were already built in. ---------------------------------------------------------------- CONNECTION The Mac end is easy. Plug it into the jack that has a speaker icon, like this one: Ê You have a few choices when it comes to the Telephone end. 1. DIRECTLY TO THE PHONE JACK Open up the jack on your wall (itÕs low voltage). YouÕll see at least one red and one green wire, connected to screw terminals. Connect a wire from the transformer to either of these screws, and from the capacitor to the other screw. 2. DIRECTLY INTO THE PHONE If youÕve got a standard, non-electronic, non-memory phone, open it up and trace the wires coming in from the back. TheyÕll connect to two screw terminals marked L1 and L2. Connect the two wires from your circuit to these screws. It doesnÕt matter which goes where. 3. JUST PLUG IT IN Get a phone cable like #279-391, with a standard modular plug on one end and four short wires coming out the other. Connect the transformer and capacitor to the red and green wires. Then plug the modular end into any standard phone jack or modular Y-connector. 4. FOR MULTI-LINE PHONES If your office phones have thick cables and 1A2 multiline connectors (they look like SCSI plugs), get a #43-270 adapter. Then use method #3, above. Digital phones Ñ found in some office buildings Ñ require a special jack. Look on the bottom of your office phone. If thereÕs a ÒRinger Equivalent NumberÓ or ÒRENÓ stamped on it, itÕs NOT digital and you can use these methods. (Touch-Toneª phones arenÕt necessarily digital.) Office telecom managers can help you get the right jack, if they can keep from laughing uncontrollably when you describe what you want to do. --------------------------------------------------------------- OPERATION Make a phone call. Play a sound on the Mac. If you donÕt hear the sound on your telephone handset, flip the switch. Set the volume with the Sound Control Panel. ---------------------------------------------------------------- AUTHORÕS NOTE The trademarks herein belong to companies with big law firms. The circuit should work and be safe. I tested both versions (and have built many for friends) and never had any problems. However, strange things can happen to Macs, lightning can strike phone lines, and klutzes can burn themselves with soldering irons. So I donÕt guarantee anything. Jay Rose Co-author ÒFirst Book of MacintoshÓ [Sams / Alpha]; wrote chapters on Sound and some other stuff in ÒEverything You Wanted to Know About the MacÓ [Hayden]. Contributing editor (on audio, what else?) to Desktop Video World. Buy my books, please. America Online: JC Rose CIS 71174,2044