SEAGATE TECHNOLOGY, INC. 1-800-SEAGATE http://www.seagate.com (C)opyright 1991 ST-3096A 4-pin DC 3-pin DC Power Power ÕÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍ͸/Ä4Ä3Ä2Ä1Ä\ ÍÑÍGÍ12Í5ѵ::::::::::ù::::::::1Ƴ 0 0 0 0 ÆÍ ³ 0 0 0 ³ÔÍÍÍÍÍÍÍÍÍÍÑÍÍÍÍÍÍÍÍ;ÀÄ5ÄGÄGÄ12Ù ÔÍ3Í2Í1; (pin-20 missing for keying purposes) User Configuration Block ³ (located behind 3-pin DC) ÀÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ 1= On, 0= Off (back of drive) 2 o-o 1 ÄÄÄ Life Test (do not use) 4 o-o 3 ÄÄÄ Master on (Slave off)ÄÄÄ 1 1 0 6 o-o 5 ÄÄÄ Slave Present ÄÄÄÄÄÄÄÄÄÄ 0 1 0 8 o-o 7 ÄÄÄ Reserved (front of drive) 10 o-o 9 ÄÄÄ Active LED S M S i a l n s a g t v l e e e r ST-3096A UNFORMATTED CAPACITY (MB) ________________N/A FORMATTED CAPACITY (xx/17 SECTORS) (MB) __89.2 ACTUATOR TYPE ____________________________STRAIGHT ARM TRACKS ___________________________________ CYLINDERS __PHYSICAL/LOGICAL______________xx/1024 HEADS ______PHYSICAL/LOGICAL______________3/10 DISCS (3.5 in) ___________________________2 MEDIA TYPE _______________________________THIN FILM RECORDING METHOD _________________________RLL (2,7) TRANSFER RATE INTERNAL (mbits/sec) _______up to 15 SPINDLE SPEED (RPM) ______________________3,211 AVERAGE LATENCY (mSEC) ___________________9.34 BUFFER ___________________________________32 KByte SeaCache INTERFACE ________________________________AT BUS SECTORS PER DRIVE ________________________174,080 TPI (TRACKS PER INCH) ____________________1,792 BPI (BITS PER INCH) ______________________31,005 AVERAGE ACCESS (ms) ______________________14 SINGLE TRACK SEEK (ms) ___________________3 MAX FULL SEEK (ms) _______________________22 MTBF (power-on hours) ____________________150,000 POWER REQUIREMENTS: +12V START-UP (amps) _0.9 POWER MANAGEMENT (Watts): ACTIVE _______________5.3 IDLE _________________2.1 STANDBY ______________0.7 SLEEP ________________0.7 WRITE PRECOMP (cyl) ______________________N/A REDUCED WRITE CURRENT (cyl) ______________N/A LANDING ZONE (cyl) _______________________AUTO PARK IBM AT DRIVE TYPE ________________________* Physical: Height (inches/mm): 1.00/25.4 Width (inches/mm): 4.02/102.1 Depth (inches/mm): 5.77/146.6 Weight (lbs/kg): 1.3/0.59 * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE AVAILABLE. (see below) Possible translation: 1024 cyl, 10 heads, 17 sectors = 89,128,960 Possible translation: 836 cyl, 8 heads, 26 sectors = 89,030,656 Note: A "custom" or "user-definded" CMOS drivetype may ask for a numerical value for the Write Precompensation cylinder and for the Landing Zone cylinder. A basic rule-of-thumb for drive models that do not require the old Write Precomp technique or a Landing Zone because they are Auto-Parking is to add 1 to the cylinder value being used. As an example: If cylinders equaled 820, then both Write Precomp and Landing Zone would be entered as 821. Some BIOS will convert this to 65535 or -1, which are functionally equivalent to "none (not used)". PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION ZBR = Zone Bit Recording = Variable sectors per track Already low-level formatted at the factory. Since a User-definable or Custom translation geometry may be used, it is imperative that the values be written down and kept with your permanent records for retrieval in the event of CMOS battery failure. Seagate reserves the right to change, without notice, product offerings or specifications. (5/13/91)